Once you see roots coming out of your starter cubes it's time to transplant. Most growers tend to use a cup (like the small, red Solo cups) to transplant their newly rooted clones into. The clones are still fragile at this point and should be treated the same as they were when they were cuttings.
Follow this link for full answer
All the same, when can I move clones to veg?
Ideally, you want the plants to finish at approximately 24 to 36 inches tall, so you will induce flowering when plants are approximately 12 to 18 inches tall. So, if you take clones (which take 14 days) and you then vegetate for 14 days, you will have both ready before your other plants have finished flowering.
At any rate, should you water clones after transplanting? Water thoroughly. It's important to give your plants a deep watering right after transplanting. This compacts the transplanting media and ensures that there are no large air pockets around the clone. It's also important to help avoid dry spots within the root ball.
Suitably, how big should clones be before transplanting?
Though some growers opt to plant their clones once the roots reach 1 inch (2.5 cm) long, it's best to wait until the roots are 3 inches (7.6 cm) or longer to reduce the chances of transplant shock.
How far should light be from clones?
With clones, they will need intense light to begin. Depending on the power of the light and maturity of the plants, this could vary quite a bit between 14-36 inches from the top of the plant canopy.
20 Related Questions Answered
To transplant:
Put soil in your pots first.Water the soil before transplanting so soil doesn't move around once the clone is in its new home.Once the water has drained, dig out a hole 1-2 inches deep with two fingers, or just enough to bury all the roots.Put the clone in and gently cover with soil.
Take clones from mother plants that are at least two months old and in the vegetative growth stage. Clones from mother plants that are less than two months old may develop unevenly and grow slowly. Clones taken from flowering plants root quickly but require several weeks to revert to vegetative growth.
It's best to take your clones at about 2–3 weeks into flowering. Once you have taken your flowering clones, it will take an average of one week until they root. The re-vegging of your clones will then take (at least) another 2–3 weeks.
The hardening process can last anywhere between 2-10 days depending on the grower and the stage of plant growth.
Water your clones with a diluted nutrient solution (400-600 parts per million or ppm) and place them under a low-intensity fluorescent fixture; T8 or T12 bulbs are ideal for this purpose, T5 bulbs are can cause plants to begin “stretching” before you are ready.
To speed up rooting, you want to cut your clones from the lower part of the mother plant. The closer to the roots they are, the faster they will root themselves. You've probably read advice that tells you to take a large section of plant with several branches and bud sites, because it speeds up the growth of the clone.
Knowing your PPM helps you avoid possible burning by letting you know when to adjust the amount of nutrient minerals you add to your water. Cannabis enjoys 500-600 ppm after cloning, 800-900 ppm when vegetating, and 1000-1100 ppm when flowering.
Dimming Capability Dimming the lights is necessary when your plants are stressed or during application of foliar and pesticides. If you choose to include dimming control in your LED grow lights, you can make sure that you are providing the right amount of light in every stage.
Veg Room Set Up A good rule of thumb is that between 10-20% of your total light wattage in the Flower Room will be used in vegetative growth. This means that if there are 50,000 watts in the Flower Room, there should be between 5,000 and 10,000 watts in the Veg Room.
The best light cycle for rooting cuttings is generally 18 hours of light and 6 hours of darkness. Do not supply cuttings with 24 hours of light without any dark periods because this has shown to slow the rooting process down as plants root best with a sufficient dark period each day.
As long as the plants are kept healthy, there's no real foreseeable limit to how long they can live and produce cuttings. Even when a clone is taken of a clone continuously, each subsequent clone should have the exact same genetic potential as the first.
There are four main ingredients in cloning solutions: gel/water/dry base, vitamins/minerals, the active ingredient, and antibacterial/antifungal elements. The three substances that stimulate root growth include napthalenaecetic acid (NAA), indolebutyric acid (IBA), and 2,4 dichlorophenoxyacetic acid (2, 4 DPA).
Over-lighting a fresh cutting can easily cause it to droop and stress. We are trying to minimize water transpiration from the leaves once the cutting has been made, so soft light is preferred for this process. One T5 over a single flat tray is adequate lighting.
Gather your supplies. Verdes uses coco coir, or coconut fiber for soil. ... Go straight home from Verdes. Be sure to head home immediately after purchasing your clone. ... Keep your clone indoors. ... Transplant as soon as possible. ... Be mindful of lighting and watering schedules.
Clones need sturdy, carbohydrate-rich fuel. When a plant is fed nitrogen, it will use up to 25 to 30% of its energy to convert those nitrates into a form of nitrogen that plants can use for vegetative growth. Using the plant's energy for growth results in fewer sugars, or carbohydrates, in the stems and leaves.
Little plants such as clones thrive in warm weather or environment. ... This is why we recommend the use of a heating pad for your clones to do well.
Cloned cuttings can't change their genetic imprint because a clone is an exact genetic replica of the mother plant. A clone is even the same cellular age as the mother plant—a one-week-old clone taken from a two-month-old mother is actually two months old.
This method is usually employed with indica strains that are packed tightly together in the grow space. When using this method, plants should be flowered when they reach a height of between 15–30cm.
How to top marijuana plants. Topping cannabis works best when a plant is strong and developed and can withstand drastic change. For the first topping—cutting the main stalk—a good rule of thumb is to cut the plant above the 5th node.
As noted, clones are simply rootless branches cut off a mother plant. During that time they'll also grow faster than plants from seeds, because the clone is not an infant, but has the same age as its mother. ... Again, this may seem advantageous at first, but such unnatural growth comes with drawbacks, too.