Can I use pre out for subwoofer?

Tennie Fergerson asked, updated on September 16th, 2021; Topic: subwoofer
👁 357 👍 9 ★★★★☆4.3

Plugging in and Hooking up Your Subwoofer If you have a subwoofer cable and a Y-adapter, this is the optimal setup for your sub. Just plug the subwoofer cable into your receiver's subwoofer pre-out and the other end into the Y-adapter on your sub (which is connected to the left and right RCA line-in inputs).

Follow this link for full answer

Therefore, what does pre out mean?

Pre-outs are used to connect an external amplifier to your receiver so they can power speakers in your Home Theater system. This is convenient if you have an extra amplifier you'd like to use or if any of your speakers require more power than your receiver alone can provide.

Afterall, what is the difference between line out and pre out? Pre-out = line level = low level. But, pre-out would typically imply "volume control" while line out would typically imply "no volume control".

Hence, how do you know when a subwoofer is blown?

Can I connect subwoofer to line out?

Yes that would work. Whatever sub you get will most likely have all of the crossover and level controls that you would need to match your speakers. All the line out is doing is sending a full range signal, (controlled by the volume control) to the the device hooked up to it.

13 Related Questions Answered

How do I turn a car subwoofer into a house sub?

How to use Your Car Subwoofer in House
  • Step One – Control the power.
  • Step Two – Connect the subwoofer to the car amplifier.
  • Step Three – Connect the car subwoofer to the home amplifier.
  • Step Four – Now connect your other speakers.
  • Step Five – Plug in the power inverter.
  • Disadvantages of Using Your Car Subwoofer in House.
  • How do you use pre out?

    The pre-out signals are drawn (copied) from the pre-amp at a point before they are sent to the internal amplifier. If you connect the pre-outs to an external power amp, the power amp then amplifies that signal and puts them out to the speakers attached to it.

    Why is preamplifier used?

    A preamplifier (preamp or "pre") is an electronic amplifier that converts a weak electrical signal into an output signal strong enough to be noise-tolerant and strong enough for further processing, or for sending to a power amplifier and a loudspeaker. Without this, the final signal would be noisy or distorted.

    How many pre outs do I need?

    Each set of pre-outs is 2 channels, so you would need two SETS of preouts for that setup. If you throw a subwoofer in there, your looking at three sets of preouts (which most good HU's will have).

    Can you split preamp outputs?

    Normally you can split the preamp output into two or three without problems - you kan even by cables that do it !

    Can I use pre outs and speaker terminals at the same time?

    Even if the internal power amp's impedance is lower than normal, it makes no difference whether speakers are connected or not. It probably is just a reminder for people who have both connected, so that they wouldn't end up using both at the same time unintentionally.

    What is LINE OUT used for?

    Alternatively referred to as audio out and sound out, the line out jack is found on computer sound cards. It allows external speakers, headphones, or other output devices to connect to the computer, transferring computer generated audio to the devices so that it can be heard.

    What does a bad subwoofer sound like?

    Partial sound with distortion - When you hear a weak, distorted sound coming from your subwoofer, at any volume, you probably have a partially blown subwoofer on your hands.

    Does a capacitor make subs hit harder?

    When required by the subwoofer, a capacitor will release the power. ... Doing so will make your subwoofers hit harder and play louder, especially in the car.

    Can blown subwoofer be fixed?

    To fix your blown subwoofer you'll need to take it out of your car, fix or replace any damaged parts, and glue/wire it back together. This process can range from easy to very difficult, depending on the problem.

    Why does my subwoofer have a left and right input?

    Dual input allows the subwoofer an extra sensitivity adjustment. Normally, it would be enough to use a mono LFE subwoofer signal from its processor. If you have a processor with very low output so you can use a Y-splitter. By using both inputs with the same mono signal doubles the subwoofer sensitivity.

    How do I install a subwoofer if I don't have a preamp subwoofer?

    If your receiver doesn't have a preamp output, you can treat the subwoofer like another speaker and use speaker wire to connect it to the receiver's speaker terminals designated for the front left and right speakers. You would then connect the front left and right speakers to the subwoofer's speaker-level terminals.

    How do I connect my subwoofer to left and right input?

    If the subwoofer's 'Line In' uses RCA cables (and if the subwoofer out on the receiver/amplifier also uses RCA), simply plug using an RCA cable and choose either the R or L port on the subwoofer. If the cable is split on one end (a y-cable for both right and left channels), then plug in both.